1892 Arduino A000024 Arduino NewCondition
Arduino Ethernet Shield 2 Without PoE

Arduino Ethernet Shield 2 Without PoE

22

Product Code : 1892

In Stock Now : 11
Incl. Tax: £22.00 Excl. Tax: £18.33
  • Arduino Ethernet Shield 2 Without PoE
  • Arduino Ethernet Shield 2 Without PoE
  • Arduino Ethernet Shield 2 Without PoE

The Arduino Ethernet Shield 2 connects your Arduino to the internet in minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 etherent cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.

  • Requires an Arduino Board (not included)
  • Operating voltage 5V (supplied from the Arduino Board)
  • Ethernet Controller: W5500 with internal 32K buffer
  • Connection speed: 10/100Mb
  • Connection with Arduino on SPI port

The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip (datasheet). The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it.

The Ethernet Shield 2 has a standard RJ-45 ethernet connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard micro-SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the Shield contained a full-size SD card slot; this is not supported.

The Shield also includes a reset controller, to ensure that the W5500 Ethernet module is properly reset on power-up. Previous revisions of the Shield were not compatible with the Mega and needed to be manually reset after power-up.

Arduino communicates with both the W5500 and SD card using the SPI bus (through the ICSP header). This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note: that because the W5500 and SD card share the SPI bus, only one at a time can be active. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output.

**This version is without PoE**

You may also be interested in the following product(s)

Arduino Uno - R3

Arduino Uno - R3

Incl. Tax: £26.40 Excl. Tax: £22.00 As low as: £21.12
EtherMega

EtherMega

Incl. Tax: £95.20 Excl. Tax: £79.33 As low as: £76.16
Arduino Ethernet Rev3 Without PoE

Arduino Ethernet Rev3 Without PoE

Incl. Tax: £43.19 Excl. Tax: £35.99
Genuino Uno Rev 3

Genuino Uno Rev 3

Incl. Tax: £24.00 Excl. Tax: £20.00

Write Your Own Review

Only registered users can write reviews. Please, log in or register