1754 Adafruit 2471 Adafruit NewCondition
HUZZAH ESP8266 Breakout view with headers

HUZZAH ESP8266 Breakout

11.34

Product Code : 1754

In Stock Now : 17
Impuestos Incluídos: 12,70 € Impuestos no Incluídos: 10,58 €
  • HUZZAH ESP8266 Breakout diagonal view
  • HUZZAH ESP8266 Breakout view connected on breadboard
  • HUZZAH ESP8266 Breakout view with headers
  • HUZZAH ESP8266 Breakout view with coin
  • HUZZAH ESP8266 Breakout close up view of top
  • HUZZAH ESP8266 Breakout diagonal view with headers attached
  • HUZZAH ESP8266 Breakout view on breadboard

Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a great price. The ESP8266 processor from Espressif is an 80 MHz microcontroller with a full WiFi front-end (both as client and access point) and TCP/IP stack with DNS support as well. While this chip has been very popular, its also been very difficult to use. Most of the low cost modules are not breadboard friendly, don't have an onboard 500mA 3.3V regulator or level shifting, and aren't CE or FCC emitter certified....UNTIL NOW!

The HUZZAH ESP8266 breakout is designed to make working with this chip super easy and a lot of fun. It is a certified module with an onboard antenna, and plenty of pins and soldered onto a specifically designed breakout PCB.

One breakout at the end has an "FTDI" pinout so you can plug in an FTDI or console cable to upload software and read/write debugging information via the UART. When you're done with your coding, remove the cable, and this little module can be embeded into your project box.

Each module comes pre-loaded with NodeMCU's Lua interpreter (NodeMCU 0.9.5 build 20150318 / Lua 5.1.4 to be specific), you can run commands, and 'save' Lua programs directly to the module's Flash using a USB-Serial converter cable. But, if you'd like, you can skip Lua and go direct to using the Arduino IDE. Once you download the ESP8266 core, you can treat it just like a microcontroller+WiFi board, no other processors needed!

Each module comes with one assembled and tested HUZZAH ESP8266 breakout board, and a stick of 0.1" header that you can solder on and plug the breakout into a breadboard. A soldering iron and solder are required for that, and aren't included. Solderless breadboard also not included. You'll really want a USB-serial cable such as a USB console cable, FTDI Friend, or FTDI cable (3 or 5V power/logic is fine) to upload software to the HUZZAH ESP8266!

Included on the board is:

  • Reset button
  • User button that can also put the chip into bootloading mode
  • Red LED you can blink
  • Level shifting on the UART and reset pin
  • 3.3V out, 500mA regulator (you'll want to assume the ESP8266 can draw up to 250mA so budget accordingly)
  • Two diode-protected power inputs (one for a USB cable, another for a battery)

Two parallel, breadboard-friendly breakouts on either side give you access to:

  • 1 x Analog input (1.8V max)
  • 9 x GPIO (3.3V logic), which can also be used for I2C or SPI
  • 2 x UART pins
  • 2 x 3-12V power inputs, reset, enable, LDO-disable, 3.3V output

Te podría(n) interesar también el/los siguiente(s) producto(s)

BLE (dual mode) Bee

BLE (dual mode) Bee

Impuestos Incluídos: 22,16 € Impuestos no Incluídos: 18,47 €
ESP8266 THING Breakout and Development Board for ESP8266 Wi-Fi Soc

ESP8266 THING Breakout and Development Board for ESP8266 Wi-Fi Soc

Impuestos Incluídos: 16,74 € Impuestos no Incluídos: 13,96 €
Espruino Pico

Espruino Pico

Impuestos Incluídos: 24,60 € Impuestos no Incluídos: 20,50 €
 

Escribir Tu Propia Revisión

Sólo usuarios registrados pueden escribir sus opiniones. Conéctese o regístrese