1858 Adafruit 2821 Adafruit NewCondition
Feather HUZZAH with ESP8266 WiFi

Feather HUZZAH with ESP8266 WiFi

18.1

Product Code : 1858

In Stock Now : 10
TTC : 20,27 € HT : 16,89 €
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi
  • Feather HUZZAH with ESP8266 WiFi

Feather HUZZAH with ESP8266 WiFi is an 'all-in-one' WiFi development board with built in USB and battery charging. An ESP8266 WiFi module with all the extras you need, ready to rock!

At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. It has a USB-Serial chip that can upload code at a blistering 921600 baud for fast development time. It also has an auto-reset function.

Its easy to use for portable projects, with a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.

Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua. (It comes pre-programmed with the Lua interpreter) It comes with some headers so you can solder it in and plug into a solderless breadboard.

Lipoly battery and USB cable not included.

Specifications:

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 9.7 grams
  • ESP8266 @ 80MHz with 3.3V logic/power
  • 4MB of FLASH (32 MBit)
  • Built in WiFi 802.11 b/g/n
  • 3.3V regulator with 500mA peak current output
  • CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading
  • Auto-reset support for getting into bootload mode before firmware upload
  • 9 x GPIO pins - can also be used as I2C and SPI
  • 1 x analog inputs 1.0V max
  • Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
  • Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

Vous pourriez également être intéressé par le(s) produit(s) suivant(s)

Feather 32u4 RFM96 LoRa Radio - 433MHz

Feather 32u4 RFM96 LoRa Radio - 433MHz

TTC : 53,75 € HT : 44,79 €
Feather M0 Basic Proto - ATSAMD21 Cortex M0

Feather M0 Basic Proto - ATSAMD21 Cortex M0

TTC : 22,19 € HT : 18,49 €
HUZZAH ESP8266 Breakout

HUZZAH ESP8266 Breakout

TTC : 12,70 € HT : 10,58 €
TFT FeatherWing - 2.4" 320x240 Touchscreen For All Feathers

TFT FeatherWing - 2.4" 320x240 Touchscreen For All Feathers

TTC : 33,31 € HT : 27,75 €

Rédigez votre propre commentaire

Seuls les utilisateurs inscrits peuvent écrire des commentaires. Veuillez vous connecter ou vous enregistrer