1292 Adafruit 1222 Adafruit NewCondition
GEMMA V2- Miniature Wearable Electronic Platform

GEMMA V2- Miniature Wearable Electronic Platform

9.92

Product Code : 1292

In Stock Now : 4
Incl. BTW: € 11,11 Excl. BTW: € 9,26

GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project!

The Attiny85 is a fun processor because despite being so small, it has 8K of flash, and 5 I/O pins, including analog inputs and PWM 'analog' outputs. We designed a USB bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino (it uses 2 of the 5 I/O pins, leaving you with 3). In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Flora. Perfect for small & simple projects the GEMMA will be your go-to wearable electronics platform.

Even though you can program GEMMA using the Arduino IDE, it's not a fully 100% Arduino-compatible. There are some things you trade off for such a small and low cost microcontroller!

  • GEMMA does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data
  • Some computers' USB v3 ports don't recognize the GEMMAs bootloader. Simply use a USB v2 port or a USB hub in between
  • We do not have full Windows 8 driver compatibility tested. At this time we only have it working with Mac, Linux or Windows 7/XP
  • Super small, only 1.1" / 28mm diameter and 0.28" / 7mm thick.
  • Easy-to-sew or solder pads for embedding in your wearable project
  • Low cost enough, you can use one for every weekend project
  • ATtiny85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM
  • Internal oscillator runs at 8MHz
  • Ultra low power, draws only 9 mA while running
  • USB bootloader with a nice LED indicator looks just like a USBtinyISP so you can program it with the Arduino IDE (with a few simple config modifications)
  • Mini-USB jack for power and/or USB uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram.
  • ~5.25K bytes available for use (2.75K taken for the bootloader)
  • On-board 3.3V or 5.0V power regulator with 150mA output capability and ultra-low dropout. Up to 16V input, reverse-polarity protection, thermal and current-limit protection.
  • Power with either USB or external output (such as a battery) - it'll automatically switch over
  • On-board green power LED and red pin #1 LED
  • Reset button for entering the bootloader or restarting the program.
  • 3 GPIO - The 3 independent IO pins have 1 analog input and 2 PWM output as well.
  • Hardware I2C capability for breakout & sensor interfacing.

U bent wellicht ook geïnteresseerd in de volgende producten

LilyPad LED White (5pcs)

LilyPad LED White (5pcs)

Incl. BTW: € 4,76 Excl. BTW: € 3,96 Vanaf: € 3,81
LilyPad Vibe Board

LilyPad Vibe Board

Incl. BTW: € 10,33 Excl. BTW: € 8,60
LilyPad Arduino 328 Main Board

LilyPad Arduino 328 Main Board

Incl. BTW: € 21,08 Excl. BTW: € 17,56
LilyPad SimpleSnap

LilyPad SimpleSnap

Incl. BTW: € 30,17 Excl. BTW: € 25,14

Schrijf uw eigen review

Alleen geregistreerde gebruikers kunnen een review plaatsen. U kunt, inloggen of registreren