Motion Controllers

Items 1 to 10 of 23 total

per page
Page:
  1. 1
  2. 2
  3. 3

Grid  List 

Set Ascending Direction
  1. NEW
    Wireless Joystick Kit

    Wireless Joystick Kit

    Incl. Tax: £31.78 Excl. Tax: £26.48

    The SparkFun Wireless Joystick Kit provides an easy way to control your next XBee project. Before the wireless joystick, radio-controlled projects used hobby RC transmitters, the same ones used for RC cars, boats and planes. The problem with these transmitters is that many aren’t customizable, and the ones that tend to be too expensive for many of us. The Wireless Joystick Kit offers a custom wireless solution for those who want to control their project their own way.

    Learn More
  2. Big Easy Driver diagonal view

    Big Easy Driver

    Incl. Tax: £21.77 Excl. Tax: £18.14

    The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It’s the next version of the popular Easy Driver board.

    Learn More
  3. Stepper Motor Driver A4988 Carrier - Black Edition diagonal view

    Stepper Motor Driver A4988 Carrier - Black Edition

    Incl. Tax: £8.17 Excl. Tax: £6.81 As low as: £7.36

    The Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than the two-layer (green) version. Like the original carrier, the Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. This board ships with 0.1″ male header pins included but not soldered in.

    Learn More
  4. AMIS-30543 Stepper Motor Driver Carrier

    AMIS-30543 Stepper Motor Driver Carrier

    Incl. Tax: £19.96 Excl. Tax: £16.63

    The AMIS-30543 stepper motor driver carrier is a Pololu carrier for ON Semiconductor’s AMIS-30543 micro-stepping motor driver, which is a high-performance stepper motor driver with advanced features not found on our other stepper motor driver carriers.

    This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step modes (from full-step through 1/128-step), back-EMF feedback that can be used for stall detection or optional closed-loop control, and over-current and over-temperature protection. The board operates from 6 V to 30 V and can deliver up to approximately 1.8 A per phase without a heat sink or forced air flow (it is rated for 3 A per coil with sufficient additional cooling).

    Learn More
  5. Servo Trigger - Continuous Rotation diagonal view

    Servo Trigger - Continuous Rotation

    Incl. Tax: £19.96 Excl. Tax: £16.63

    The continuous rotation (CR) servo trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal changes state, the CR Servo Trigger is able to tell an attached servo motor to move from position A to position B. To use the CR Servo Trigger, you simply connect a hobby servo and a switch, then use the on-board potentiometers to adjust the start/stop positions and the transition time.

    Learn More
  6. 16-Channel PWM / Servo HAT for Raspberry Pi top view

    16-Channel PWM / Servo HAT for Raspberry Pi

    Incl. Tax: £17.38 Excl. Tax: £14.48

    The 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins!

    Learn More
  7. Line Follower Array diagonal view

    Line Follower Array

    Incl. Tax: £28.37 Excl. Tax: £23.64

    The Line Follower Array is a long board consisting of eight IR sensors that have been configured to read as digital bits! It has been designed to follow a dark line of about ¾ inch width or smaller (spray paint or electrical tape) on a light background. Each array features visible LEDs that point upward when the board is attached (properly) so you can see what the robot sees, brightness control right on the board, and an I2C interface for reading and power control.

    Learn More
  8. Adafruit Motor Shield Kit for Arduino v2.3 diagonal view

    Adafruit Motor Shield Kit for Arduino v2.3

    Incl. Tax: £19.86 Excl. Tax: £16.55

    The Adafruit motor shield kit for Arduino gives you the ability to drive up to 4 DC motors or 2 stepper motors and can be stacked to add more motors, leaving the pins on the Arduino free for more inputs and outputs for sensors.

    Learn More
  9. 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685 diagonal view

    16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

    Incl. Tax: £14.90 Excl. Tax: £12.42

    With this 16 channel 12-bit PWM servo driver, using only two pins, you can control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs!

    Learn More
  10. Dual MC33926 Motor Driver for Raspberry Pi diagonal view

    Dual MC33926 Motor Driver for Raspberry Pi

    Incl. Tax: £29.74 Excl. Tax: £24.78

    The Dual MC33926 motor driver add-on board enables a Raspberry Pi B+, A+, or Pi 2 to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor. The default pin mappings make it easy to get started and the board also exposes most of the driver chip's I/O pins for more specialized applications. This version ships fully assembled with connectors soldered in.

    Learn More

Items 1 to 10 of 23 total

per page
Page:
  1. 1
  2. 2
  3. 3

Grid  List 

Set Ascending Direction